Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
We have unearthed the article about Installing A Bathtub down the page on the web and decided it made sense to talk about it with you on this site.
Mounting a tub isn't specifically rocket science, yet it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably challenging task. If the old tub is easily accessible, the project can relocate speedily; if you have to open a wall surface to remove the old bathtub and position the brand-new tub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the new one. See to it you have certified on your own for the task and also are comfortable trying it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to think about utilizing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This short article will certainly aid you set up a brand-new bath tub in your restroom if you have actually currently bought a new bathtub and don't require to transform the arrangement of your previous supply of water pipelines.
Your devices and material list need to comprise the following:
Getting ready for the Installment
To start with, the supporting frame provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub up until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet adapter to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water as well as examine all joints and brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and additionally check the overflow outlet and also the normal electrical outlet for leakages.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been made use of a minimum of when as this will settle it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break a rigid seal, causing the water to penetrate the wall between the bath and the tiling, leading to complications with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealant can crack rather very early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently readily available on the marketplace. It is a good idea to fit the tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader on How to Install a Bathtub Yourself, I figured sharing that excerpt was sensible. Liked our piece of writing? Please share it. Help somebody else check it out. Many thanks for your time spent reading it.
Schedule Your Service Report this page